![]() I have not seen any others that would work, so I assume this beveled gasket is what I should be using.Īny help / advice would be much appreciate. The old gasket was really dried out and fragmented so I am not sure if I am even using the right kind of gasket. I don't see much purpose in those posts other than keeping the gasket from shifting inwards. One of the posts is already broken off - is there any reason that I should not snap off the other three? If they were not there I think I would be able to work the gasket in place. In all the online video/pics I do not see a drain that has these posts (as well as the single screw hole in the center). The DANCO Waste and Overflow Gasket fits between a tub and overflow drain and provides a positive seal to help prevent leaks. The cover is available in Chrome, Brushed Nickel, and Oil-Rubbed Bronze finishes. The drain does not have enough give to push it far enough back to get the gasket over the little plastic posts. It works for center hole overflow pipes (single-screw mount) and/or overflows with one screw on each side (double-screw mounts). ![]() What is giving me trouble are the little posts that are sticking out around the drain (see picture). The inner diameter of the gasket is the exact same as the diameter of the hole in the tube (see picture) - I assume that is the size it should be. The varied bevel thickness seems correct. If you have access behind the shower wall to open it up and I would changed out the valve body with a Delta tub shower valve body.I am struggling with trying to get a new beveled overflow gasket I purchased. A little silicone behind the spout is OK but I prefer siliconized caulk.Īs John suggest you can replace everything. Delta Faucet RP7420 Overflow Plate Beveled Gasket,Chrome. The distance between the center of the vertical tubular vent line and the center of the tub drain itself cannot exceed 7-1/2' or be less than 6-3/4'. FREE Shipping on orders over 25 shipped by Amazon. Fits overflow elbow 11009 Fits many Watco brand overflow elbows Dimensions: 3-1/2' OD x 2-1/4' ID x 5/8' Thick 2.88 : Enter a quantity and. Remove the spout either with a set screw or it untreads. 4 Pcs 1-3/4-Inch by 2-5/8-Inch Rubber Gasket for Tub Drain Shoe Tub Overflow Gasket Silicone Bathtub Drains Seal. the handle should not go past these positions. 3 o'clock is full cold, 9 o'clock is full hot. These MOEN's you pulled out the handle to run the water. This Moen cartridge stem may be missing external stops under the handle or they were build into the handle. It looks like it is all brass and it should last a lifetime. Do replace the washer between the tub and drain shoe. Do clean the area behind the tub and as John suggest, remove the level mechanism and replace it with a plain overflow. ![]() However do buy a replacement gasket and remove the old one and wiggle in a new one careful it doesnt fall behind the tub. No reason to replace the drain assemble., just the top side from the tub. Overflow gaskets do not leak unless the tub is filled to the overflow level. I placed the gasket on the inside of the tub, not between the overflow pipe and the tub. Here is a picture of the tub and overflow drain. ![]() Westbrass D493CHM-26 Universal Patented Deep Soak Round Replacement 2-Hole Bathtub Overflow Cover for Full and Over-Filled Closure, 1 Pack, Polished Chrome - LOGO. Plumbing and Piping - BathTub Overflow Gasket. The only place to use silicone would be under the drain flange. DANCO Tub Stopper Gasket for Tub Drain Assemblies (37680B), Black. Do clean the area behind the tub and as John suggest, remove the level mechanism and replace it with a plain overflow.Īt the drain replace it with a toe stopper. However do buy a replacement gasket and remove the old one and wiggle in a new one careful it doesn't fall behind the tub. Click to expand.Overflow gaskets do not leak unless the tub is filled to the overflow level. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |